Selection
Selection names a part of a mesh or curve, so later nodes can work on just that part: every face pointing up, the sharp edges, a box full of points, or faces you click. The geometry passes straight through with the name attached; nothing changes until a later node picks the name in its Apply to setting. Use it to bevel only the outer edges, roughen only the top, or delete one face.
Imported parts
Section titled “Imported parts”On an imported model, set Method to Parts to select whole parts of it by name: the wheels, the
cabin, a door. You rarely set this by hand: clicking a part in the viewport adds a Parts Selection
after the node you clicked and makes it the selected node. Shift/Ctrl+click adds or removes parts, and
its name follows the parts (Wheel_FL_pick, Wheel_FL_plus2) until you rename it. Press Delete to
remove the picked parts (the Selection stays, with a Delete after it), or press Esc to drop the pick
and leave the graph as it was. Later, select that Selection and Shift/Ctrl+click parts to change
which ones it covers. A part the model no longer has shows amber in the list and selects nothing.
Inputs
Section titled “Inputs”The mesh or curve to select part of.
Outputs
Section titled “Outputs”The same geometry, carrying the named selection to later nodes.
Parameters
Section titled “Parameters”| Parameter | What it does | Default |
|---|---|---|
Type | What to select on a mesh: Points, Edges or Primitives (faces). Options: Points, Edges, Primitives Shown for a mesh input. | Edges |
Name | The name later nodes use to pick this selection in their Apply to setting. | Blank |
Existing | What to do if the mesh already has a selection with this name: Replace it, Add to it, Remove from it, or keep only what both share (Intersect). Options: Replace, Add, Remove, Intersect | Replace |
Method | How pieces of the curve are chosen: by a stretch along it (U range), by a box (bounds), or by clicking them (Manual). Options: By U range, By bounds, Manual Shown for a curve input. | By U range |
Spans | The curve pieces you clicked in the viewport. Shown for a curve input when Method is Manual. | Set in the viewport |
U start | Where the selected stretch begins, from 0 at the curve's start to 1 at its end. Shown for a curve input when Method is By U range. | 0 |
U end | Where the selected stretch ends. U start 0 and U end 1 select the whole curve. Shown for a curve input when Method is By U range. | 1 |
Center | The center of the box that picks curve pieces. Shown for a curve input when Method is By bounds. | 0, 0, 0 |
Size | The size of the box along each axis. A piece is selected when most of it is inside. Shown for a curve input when Method is By bounds. | 2, 2, 2 |
Method | How edges are chosen: by how sharp they are (angle), by the way they face (normal), or by clicking them (Manual). Options: By angle, By normal, Manual Shown for a mesh input when Type is Edges. | By angle |
Min angle | How sharp an edge must be to be selected, in degrees. 90 is the edge of a box; the default skips flat areas. Shown for a mesh input when Type is Edges and Method is By angle. | 40 |
Max angle | The sharpest edge that is still selected, in degrees. 180 has no limit. Shown for a mesh input when Type is Edges and Method is By angle. | 180 |
Spread | Grows the selection outward by this many rows of neighboring edges. Shown for a mesh input when Type is Edges. | 0 |
Edges | The edges you clicked in the viewport. Shown for a mesh input when Type is Edges and Method is Manual. | Set in the viewport |
Method | How faces are chosen: by an attribute value, by clicking them (Manual), by the way they face (normal), or by imported parts. Options: By attribute, Manual, By normal, Parts Shown for a mesh input when Type is Primitives. | By attribute |
Parts | The imported parts this selection covers. Shown when Type is Primitives and Method is Parts. | None |
Attribute | The attribute to match, such as the tag a Boolean put on the faces it cut. Picked from the input mesh. Shown for a mesh input when Type is Primitives and Method is By attribute. | None |
Value | The value a face's attribute must have to be selected. Picked from the input mesh. Shown for a mesh input when Type is Primitives and Method is By attribute. | None |
Faces | The faces you clicked in the viewport. Shown for a mesh input when Type is Primitives and Method is Manual. | Set in the viewport |
Method | How points are chosen: by the way they face (normal), by clicking them (Manual), or by a box (bounds). Options: By normal, Manual, By bounds Shown for a mesh input when Type is Points. | By normal |
Points | The points you clicked in the viewport. Shown for a mesh input when Type is Points and Method is Manual. | Set in the viewport |
Center | The center of the box that picks points. Drag it in the viewport too. Shown for a mesh input when Type is Points and Method is By bounds. | 0, 0, 0 |
Size | The size of the box along each axis. Shown for a mesh input when Type is Points and Method is By bounds. | 2, 2, 2 |
Direction | The direction to compare against: 0, 1, 0 picks what faces up. Shown for a mesh input when Type is Edges and Method is By normal, or Type is Primitives and Method is By normal, or Type is Points and Method is By normal. | 0, 0, 1 |
Spread angle | How far from Direction something may face, in degrees, and still be selected. Shown for a mesh input when Type is Edges and Method is By normal, or Type is Primitives and Method is By normal, or Type is Points and Method is By normal. | 45 |
Include opposite | Also selects what faces the opposite way, such as both the top and the bottom. Shown for a mesh input when Type is Edges and Method is By normal, or Type is Primitives and Method is By normal, or Type is Points and Method is By normal. | Off |
See also
Section titled “See also”- Bevel: bevel only the selected edges.
- Noise: roughen only the selected part.
- Delete: remove the selected part, or keep only it.
- Utility nodes: the other plumbing nodes.