Skip to content

Polyreduce

Polyreduce lowers a mesh’s triangle count while keeping its shape and sharp edges. Reduce to a set number of triangles, keep a fixed share of them for a lower-detail version of a model, or reduce only as far as the shape allows to clean up a heavy import. By default UVs and materials survive, so a painted mesh stays painted. Geometry for rebaking instead prepares an untextured surface for a fresh unwrap and bake.

Any geometry

The mesh to make lighter.

Same as input

Fewer triangles with existing textures preserved by default; Geometry for rebaking returns an untextured mesh for Auto Unwrap and Bake.

Parameter What it does Default
Texture handling Keep existing UVs, or spend the triangle budget on shape and rebuild textures downstream. Options: Preserve existing textures, Geometry for rebaking Preserve existing textures
Mode How far to reduce: keep a share of the triangles, go only as far as the shape allows (good for cleaning up a heavy imported model), or reduce to a set number of triangles. Options: Keep ratio, Within tolerance, Target triangles Within tolerance
Keep ratio How much of the mesh to keep: 1 requests the input count, 0.5 requests half. Continuation can reduce further. Shown when Mode is Keep ratio. 0.5
Continue reducing within quality tolerance After reaching the count target, keep removing edges within the quality tolerance. Shown when Mode is Keep ratio, or Mode is Target triangles. Off
Quality tolerance How much the shape may change. Larger removes more. Shown when Mode is Within tolerance, or Continue reducing within quality tolerance is On. 0.00001
Target triangles How many triangles to end with. With continuation off, a mesh already below the target is unchanged. If borders or texture seams stop the reduction early, the node warns with the count it reached. Shown when Mode is Target triangles. 10000
Boundary weight How firmly open edges hold their shape. Higher keeps the outline tighter; 0 lets it shrink. 1
Sheet guard Stops thin two-layer surfaces, like cloth, from poking through themselves. Full checks everywhere and is slow on big meshes; Fast checks only where two layers sit within a few millimetres; Off is fastest. Options: Full, Fast, Off Off
UV seam weight Applies when preserving textures. How firmly texture seams hold their shape. Higher stops a curved seam from straightening; textures stay intact either way. 1
  • Within tolerance, the default, reduces while collapse costs stay within Quality tolerance. Use it to clean up a heavy import without choosing a number. At its default settings it removes what the shape doesn’t need: a 1,000,000-triangle hut comes down to about 33,000 triangles with its shape within about a millimetre and its textures intact.
  • Target triangles reduces to the number you type, whatever the input. Use it when the result has a budget, such as a 10,000-triangle game prop made from AI-generated models that arrive anywhere between 80,000 and over a million triangles. With continuation off, a mesh that already meets the target is left unchanged. A quad counts as two triangles.
  • Keep ratio keeps a share of the triangles. Half of a 200,000-triangle mesh is 100,000, and half of a 20,000-triangle one is 10,000.

A Polyreduce saved before Within tolerance became the default keeps the mode it was saved with.

Open edges, texture seams, material borders and separate parts hold their shape, so they can stop Target triangles before it reaches the number. When that happens the node shows an amber warning with the count it reached.

Thin parts built from two close sheets, like cloth with a front and a back, can poke through themselves when reduced hard: the inner side shows through as dark patches. Sheet guard stops that, at a cost.

  • Off, the default, checks nothing. It is the fastest, and right for most imports: on a 1,000,000-triangle hut the check took about 40% of the reduction and changed nothing you could see.
  • Fast checks only where two sheets of one part sit within 5 mm of each other (or 2% of the part’s size, if that is less), like the layers of a hood or a cape. Use it on characters and clothing. On the hut it runs as fast as Off.
  • Full checks every collapse against the whole part. Use it when two sheets further apart than 5 mm still cross under Fast. It is the slowest.

Separate parts are never checked against each other, so planks pressed together reduce as if apart.

Preserve existing textures is the default. Geometry for rebaking frees the reduction from the original UV seams so more of the triangle budget can preserve shape. It returns untextured geometry: UV sets, materials and other corner channels are removed, even if the mesh already meets the count target. Face attributes and separate parts remain.

Use Import → Polyreduce → Auto Unwrap → Bake, with a second wire from the original Import to Bake’s source input. Set Polyreduce to Geometry for rebaking, choose a triangle budget, and disable continuation for a fixed budget. The UV seam weight has no effect in this mode. Rebaking can recover shading detail, but cannot restore missing silhouettes or holes.

Continue reducing within quality tolerance

Section titled “Continue reducing within quality tolerance”

Enable this in Keep ratio or Target triangles to simplify further after reaching the requested count. The count is reached first, even if doing so exceeds the tolerance. Quality tolerance then controls additional reduction; higher values permit more. A value of zero still removes zero-cost edges, while disabling the checkbox stops at the count target.

The threshold is the square of Quality tolerance times total input surface area. It compares individual collapse costs, not maximum point movement or accumulated surface error. Adding another disconnected piece changes the total area and can change how far reduction continues. Within tolerance mode applies this same rule from the beginning, without a count reduction first. Existing graphs using that mode may produce different results than the former calibrated rule.

  • Remesh: rebuild the surface as even triangles instead.
  • Import: bring in a heavy model to reduce.
  • Topology nodes: the other nodes that change the polygon count or layout.